Call 8am-5pm MT M-F 1-866-724-6240

Thursday, September 1, 2011

What is a Pressure Switch?


A pressure switch is a device that is configured to sense a change in a certain pressure on something and then react in a certain manner. Pressure switches are used on many devices such as electric and gas heaters, pumps, small air compressors, electric strip heaters, food processing equipment, and of course on many hot tub heaters.

When it comes to your hot tub, the pressure switch (also often referred to as a flow switch), makes sure that water is flowing while your heater is on so that in the event water is not flowing your heater will not over heat, and burn itself up. It is a safety feature that keeps the heater from turning on when there is not water flowing. The switch senses water pressure and if the pressure is where it should be the switch completes the circuit of electricity to the heater.

If you are having trouble with your spa heating or heating insufficiently, the problem may not be with your heater. It could be a pressure switch issue. If your pressure switch is not working properly it could cause the water not to heat, but always make sure you have water flow because the spa not heating could also just be the pressure switch doing its job.

Monday, August 15, 2011

Why did I get a Rash from my Hot Tub?

Your hot tub is supposed to be your relaxing oasis, the last thing you want is for it to leave you with red irritating bumps all over your skin. Unfortunately, this can be a common problem if your hot tub sanitizer is too low and not being maintained properly.

Warm water can be an ideal breeding ground for microorganisms such as bacteria, fungi, protozoa's, and viruses. Sanitizers in spas such as bromine or chlorine are used to kill these microorganisms, and maintain safe, clean water for bathers. People often think they are allergic to spa sanitizers after developing a rash from bathing, but usually the culprit is actually inadequate sanitizer which leads to the buildup of microorganisms that can cause skin irritation and rash.

Hot Tub Folliculitis is a common condition caused by Pseudomonas bacteria, and can often be found where there is a spa sanitation issue. The symptom most often associated with hot tub folliculitis is small reddish bumps or an itchy rash; it can commonly be confused as a bug bite. With Hot Tub Folliculitis bumps can cover the entire body but tend to be more prominent in areas where the bathing suit covers. If you develop symptoms it is best to contact your health care provider, although the symptoms typically clear on their own after a few days. Also keep in mind that while your doctor is an expert in human conditions, they may not be an expert in proper spa care so please follow the tips below to keep your spa safe and microorganism-free!

Proper Care Tips to Avoid Contamination:

· Refill your spa with fresh clean water at least every 4 months. The use of a Spa Pure Pre-Filter may help in getting you water balanced properly from the get go.

· Maintain proper sanitizer levels, whether you are on a bromine, chlorine, or biguanide system.

· Shock treat regularly, especially after heavy usage.

· Test your water often using proper test strips or test kit!

· Maintain proper pH and alkalinity levels.

· If your spa cover is in poor condition, smells, or is water logged---replace it. It will not only help fight microorganisms but also help with energy savings.

· Before each drain and refill purge your spa of any build up using Spa Purge!

· Give your filters a deep clean at each drain and refill, and replace them when needed.

By properly caring for your hot tub you can ensure that it is a healthy and safe environment for all those who enjoy it.

Friday, July 22, 2011

Hot Tub Mineral Systems

Hot Tub Mineral Systems

Mineral care is not a replacement for bromine or chlorine, but works together with it and allows you to keep bromine or chlorine levels much lower than would normally be needed. With a mineral system you can keep bromine or chlorine levels as low as 1.0 part per million (ppm), this allows you to have clean sparkling water without the negative affects of chlorine or bromine like stinky chemical odors and fading swimming suits.

How Does It Work?

Mineral Systems come in a few different brands and forms. At Hot Tub Warehouse, we carry Spa Frog Minerals. These systems uses and active ingredient of Silver Chloride that destroys bacteria while neutralizing acid, this helps to keep pH in the proper range with little maintenance.

The Filter Frog system is used with a design that allows the unit to fit right inside most spa filters, and it lasts for 4 months at a time. Releasing minerals into the water as it flows over it.
The other option is the Spa Frog Mineral Cartridges which are used together with Spa Frog Bromine Cartridges in either a floating or inline system. These cartridges release minerals into the spa and also need to be replaced every 4 months.

What levels should be maintained?

When using a mineral system keep in mind that it cannot be used alone, but together with either bromine or chlorine! Whenever you start with fresh water, which should be at least every 4 months, you need to be sure and give the water an initial shock treatment to establish a residual level of chlorine or bromine at 1.0-2.0 ppm. After initial water balancing levels should be maintained as follows:

pH: 7.2-7.8
Total Alkalinity: 80-180 ppm
Calcium Hardness: 150-400
Chlorine or Bromine- 1.0-2.0 ppm

It is a good practice to continue to shock treat your water once per week or more depending on use.

Using a mineral system can be a great option to kill bacteria in your spa water while maintaining water clarity, keeping pH in neutral territory, and reducing bromine or chlorine usage for softer and more comfortable water.

Friday, April 15, 2011

Replacing My Spa Pack


Your Spa Pack is basically the brains, or motherboard of your spa. Its job is controlling all your spas components like your pump, heater, lights, and more. As the main control system, having a Spa Pack that is in good condition and working properly is very important. Thousands of spas are thrown out each year because of bad control systems, when the shell and cabinet are fine. Typically, you can save yourself thousands of dollars by simply replacing your control system rather than your entire hot tub. If your spa gets a lot of use or is over 7 years old it can be expected that the control system will need to be replaced. Spa cabinets and shells have a much longer life span than control systems, which means you can take advantage of that by replacing the spa pack once or twice during the shell and cabinet lifespan before throwing your tub out and investing in a new one.

When shopping for a new spa pack it is important for you to know a few things about your existing one. For starters, is it a 120 Volt or a 240 Volt system? What combination of items is your existing pack controlling? How many pumps do you have and how many speeds do each of those pumps have? Do you have an ozonator? What about lights? How many kilowatts is your heater? Do you have a blower, circulation pump, or both? Once you know what you need to control you can start shopping.

When shopping the easiest thing to start out doing is find control systems that match the capability of your existing system. For example, if your current system runs on 240 Volts and controls a 5.5 KW heater, a two speed pump, an ozonator, and a light that is what you need to look for.

There are a few other important things to consider when shopping for a control pack. Do you also need a new topside control system? Although you can keep your old one if it is working properly and you make sure it is compatible with your new system, we recommend looking at a Value Pack Control System like these from Balboa, they include a new topside control panel, your new spa pack, a new heater, all applicable cords, and an adapter plate to ensure your new topside control can fit correctly. You will also find that usually a Value Pack like these is much more cost effective than purchasing the items separately. You will also want to look for features that protect the pack against corrosion and water intrusion; the M7 packs from Balboa have a plastic enclosure included that will protect against these elements. When purchasing, also be sure to look for a manufacturer’s warranty on the pack just in case something does go wrong with it.

Once you have purchased a new spa pack, it is recommended to have it installed by a professional spa technician, but if you find yourself to be very handy and take the proper precaution’s for working with electrical parts, there is most often a wiring diagram and instructions for installation included.

Tuesday, March 29, 2011

Ozone and Ozonators



First of all you are probably asking, what is ozone? Ozone is a form of oxygen that is created when electrical energy breaks apart an ordinary oxygen molecule starting a chemical reaction which results in ozone. Oxygen molecules are split, by a high-energy electrical discharge, resulting in two individual oxygen atoms and those individual oxygen atoms unite with remaining oxygen molecules to produce a three-atom molecule of ozone. The weak bond holding ozone’s third oxygen atom causes the molecule to be extremely unstable and thus, very effective as an oxidizer. An oxidation reaction occurs upon any collision between an ozone molecule and an organic molecule, such as bacteria, viruses, fungus and algae, where the oxygen atom held by the weak bond splits off and only oxygen is left behind.

Next I know you are thinking, that is a great chemistry explanation but how does ozone work? An ozonator system duplicates this process and produces ozone safely and in controlled amounts that can help the sanitizing system in your hot tub. When used together with a sanitizer like bromine or chlorine, an ozonator can deeply reduce the levels of chlorine or bromine needed to maintain clean water. This allows you to save money on chemical costs. Ozone has also been credited with helping extend the life of your equipment, reducing maintenance time and cost, and it purifies your water naturally. Ozone eliminates the need for weekly shock treatments as ozone is an automatic, daily, non-chlorine shock. With ozone you will be able to use 60-90% less chlorine or bromine which allows your ozonator to quickly pay for itself.

In order for an ozonator to be effective in helping sanitize your water it needs to run for 4-6 hours per day. 90% of all new spas come equipped ozonator ready and it is very easy to install an ozonator if it did not already come with one. Ozonators do need to be replaced about every 3 to 5 years so if you do have an older one and it doesn’t seem to be working as well as it used to it is probably time for a new unit.

If you a buying an ozone unit for the first time there are a few things to consider to make sure you get the best one for your specific tub.

Spa Size: The larger your spa the more powerful ozonator you will need.

Sanitation Level Needed: If you often have large groups of people using your hot tub, you will want an ozonator that has a more powerful sanitation output.

Electrical Needs: You will need to determine what voltage and style cord you need. Ozonators come with a variety of different cords and in 120 volt, 240 volt, or dual voltage options.

Ozone is a great option for your spa in providing a natural sanitizing system while allowing you to save money on chemicals. You will eliminate the need for weekly shocking, which will also save you time. Who doesn’t like to save time and money? With ozone you will have the cleanest, clearest sparkling water that can be found in any hot tub!